Skip to main content
Rockwall Handyman Co.
Home Maintenance

Make-Ready and Punch Lists: One List, Not Ten Calls

6 min read · Published

Most houses don't need one big repair before a sale or a new lease. They need twelve small ones. A door that won't latch, two nail pops, a scuffed hallway, a dripping faucet, a gate that drags, a towel bar that pulled out of the wall. None of them is hard. The hard part is that they belong to five different trades, and calling five people for twelve small jobs is how a two-day list turns into three weeks.

This guide covers how to write that list, what belongs on it, what doesn't, and how to get it done in as few visits as possible. It's the same process whether you're a homeowner listing a house, a landlord between tenants, or an agent working through an inspection report.

The three times a make-ready list shows up

  • Before listing. You want the house to photograph well and to give a buyer's inspector as little to write up as possible.
  • After the inspection. The buyer's inspector has written a report, and some of its items need doing before closing. The deadline is fixed and short.
  • Between tenants. The last tenant is out, the next one has a move-in date, and the unit needs to be patched, painted and working in between.

The list looks similar in all three. What changes is the deadline and who's reading the result.

Write one list, not ten calls

Walk the house once, start to finish, with a notepad or your phone. Go room by room in the same direction so nothing gets skipped, and include the garage, the yard and the fence line. Write every item with where it is: "primary bath, faucet drips", not just "faucet". Take a photo of each one.

Open and close every door. Turn every light and fan on and off. Run every faucet and flush every toilet. Look at the ceilings, because that's where water stains and nail pops hide. Walk the fence and swing the gates. Most of what an inspector finds, you can find first this way.

If you have an inspection report or a move-out checklist, merge it into your list so there's one document. Three overlapping lists is how items get missed.

What usually ends up on the list

  • Drywall: nail pops, doorknob holes, anchor holes, settling cracks, small water stains
  • Paint: scuffs, touch-ups, a room or hallway that needs a full coat, trim and doors
  • Doors and locks: doors that rub or won't latch, loose hinges, worn locksets, missing door stops
  • Trim and caulk: loose baseboard, split casing, cracked caulk at tubs, sinks and counters
  • Fixtures: dead or dated light fixtures, wobbly fans, missing switch and outlet covers
  • Plumbing fixtures: dripping faucets, running toilets, slow or jammed disposals, stiff shut-off valves
  • Outside: gates that sag, loose fence boards, soft deck boards, wobbly railings
  • Odds and ends: towel bars, blinds, screens, cabinet hardware, smoke detector batteries

Every item on that list is handyman work. That's the point of sending it to one person.

What doesn't belong on a handyman's list

Some items need a licensed trade, and the honest move is to pull them out early so they get scheduled in parallel instead of discovered on the last day:

  • Electrical panel work, new circuits or anything an inspector calls a wiring hazard
  • HVAC service or repair
  • Roof repairs and active leaks from above
  • Foundation evaluation or repair
  • Gas lines and gas appliances
  • Water heaters, and plumbing inside walls or under the slab

When we quote a list, we mark these lines for a specialist rather than skip them silently, so you know exactly which calls you still have to make.

Do the work in the right order

Order matters more than people expect. A sensible sequence is:

  1. Repairs: doors, hinges, plumbing fixtures, loose trim, fence and deck fixes
  2. Drywall patches and crack repairs, with enough drying time
  3. Paint and touch-ups
  4. Hardware, fixtures, covers and anything that mounts on a finished wall
  5. A last walk-through, touch-ups and clean-up

Painting over a crack that hasn't been retaped just means the crack comes back in a few weeks, usually right after the buyer moves in. Hanging a new fixture before the ceiling around it is painted means taking it down again.

Working from an inspection report

Inspection reports are long, and not every line is a repair. Some are notes, some are maintenance suggestions, and some are items the buyer and seller will negotiate over. Decide with your agent which items are actually getting done, then send us that list along with the report pages. We quote the lines in our trades, mark the specialist items, and schedule around your closing date.

Keep the invoice. If repairs are part of the contract, the buyer's side will often want to see what was done.

Tenant turns

A turnover list is mostly the same items every time, which makes it easy to speed up:

  • Pick one wall color and sheen for the whole unit and write it down. Next turn, touch-ups blend instead of needing a full repaint.
  • Take move-out photos room by room before anything is fixed. They settle deposit questions and make the list easy to send.
  • Consider a keypad deadbolt. Changing a code between tenants is quicker than changing locks.
  • Batch small repairs that come up mid-lease into the next turn when they can wait, and call for the ones that can't.

If you manage several properties, it's worth having one handyman who knows them. We work with property managers and landlords on exactly that.

How it's priced and how long it takes

We quote a make-ready by the list, not by the hour, so you know the total before work starts. Photos of each item help us quote before the visit and bring the right parts and matching materials the first time.

Most standard lists can be cleared in one visit. Longer lists, full repaints, or drywall repairs that need drying time between coats may need a second day, and we'll tell you that up front so you can plan around a listing date or a move-in.

The short version

Walk the house once and write everything down with its location. Pull out the licensed-trade items early. Do repairs before patches, patches before paint, and paint before fixtures. Then hand one list to one person. If that person is us, start with our make-ready and punch list service, or if you're an agent, see how we work with realtors.

Need this done?

Request a free quote, call, or text us a photo. We'll get back to you fast.

Most requests answered within a couple of hours, Mon-Sat.

Frequently asked

Common questions

What's the difference between a make-ready and a punch list?+

A make-ready is the work that gets a property ready for its next occupant: a buyer, a tenant or a guest. A punch list started as the list of small unfinished items at the end of a construction job. In practice people use the two words for the same thing: one list of small repairs that all need doing before a date.

Can you work from my inspection report?+

Yes. Email it to sales@i30builders.com or paste the items into the quote form. We quote the line items that fall within our trades and mark the ones that need a licensed specialist, so you know which calls you still have to make.

Should I fix everything on the inspection report?+

Not necessarily. Which items get fixed, credited or left alone is a negotiation between you, the buyer and your agents. What we can do is price the items quickly, so that conversation happens with real numbers instead of guesses.

How is a punch list priced?+

We quote by the list rather than by the hour, so you know the total before work starts. Small items on the same visit are usually combined into one fair price instead of being charged one trip at a time.